Sensors odd cpu temp

Forum Forums General Software Sensors odd cpu temp

  • This topic has 13 replies, 5 voices, and was last updated Sep 12-10:07 pm by Koo.
Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • #66800
    Member
    palacca

    Here’s what I get running “sensors”:

    $ sensors
    acpitz-virtual-0
    Adapter: Virtual device
    temp1:        +40.0°C  (crit = +100.0°C)
    

    Always, no matter how much of my cpu I’m using, I find it quite confusing as even in bios cpu temp is higher (45-50°).
    Among solutions I tried to run “sensors-detect”, here’s the output:

    Driver it87:
      * ISA bus, address 0x290
        Chip ITE IT8705F Super IO Sensors (confidence: 9)
    

    I tried to add it in /etc/modules but at boot I get a message like “driver it87 is busy”, and nothing changes.
    As a new user I don’t know if that is an hw or software issue, does anyone have any advice?
    I was also looking for some GUI software to see if it changed things, found CPU-X but I can’t find a way to install it.
    Thanks for your time.

    • This topic was modified 2 weeks, 2 days ago by palacca.
    #66815
    Member
    Xecure
    Helpful
    Up
    0

    On my laptop:

    $ sensors
    BAT1-acpi-0
    Adapter: ACPI interface
    in0:          12.50 V  
    curr1:       1000.00 uA 
    
    coretemp-isa-0000
    Adapter: ISA adapter
    Package id 0:  +66.0°C  (high = +87.0°C, crit = +105.0°C)
    Core 0:        +62.0°C  (high = +87.0°C, crit = +105.0°C)
    Core 1:        +66.0°C  (high = +87.0°C, crit = +105.0°C)

    acpitz-virtual-0
    Adapter: Virtual device

    Maybe there is a problem in the VM to recognize properly the battery. Maybe kernel related.

    I was also looking for some GUI software to see if it changed things, found CPU-X but I can’t find a way to install it.

    Unfortunately, it isn’t in the debian repos for Debian buster (Debian 10 – antiX 19).
    But it does seem to be present in Debian bullseye (so you could try to see if anything is different in the antiX 21-b2 beta release)

    antiX Live system enthusiast.
    General Live Boot Parameters for antiX.

    #66829
    Member
    palacca
    Helpful
    Up
    0

    Unfortunately, it isn’t in the debian repos for Debian buster (Debian 10 – antiX 19).

    Is there any other alternative that can be used with antix19?

    • This reply was modified 2 weeks, 2 days ago by palacca.
    #66844
    Moderator
    ModdIt
    Helpful
    Up
    0

    Too busy complaining about USB stick recognition to do a 2 second search. !!!!

    Appimage from CPU-X GIT page runs fine.

    You can also follow instructions from said page to compile and install.

    #66847
    Member
    Xecure
    Helpful
    Up
    0

    Moddit, I think you have confused the users.

    @palacca, investigating a bit more I found that cpu-x build their own .deb packages that should also work on antiX 19
    Download and uncompress this file, Go to the Debian 10 folder and the correct architecture folder, and install it in the system by opening a terminal, writing (without executing yet)
    sudo apt install
    leave a space after “install” and drag and drop the .deb files cpu-x_4.2.0-1+1.1_amd64.deb and libcpuid15_0.5.1-0_amd64.deb.
    Then hit Enter in the terminal and it should install cpu-x and its dependencies.

    antiX Live system enthusiast.
    General Live Boot Parameters for antiX.

    #66855
    Member
    Koo
    Helpful
    Up
    0

    @palacca
    What model motherboard are you using..
    I have this it8665 sensor chip and need to load the modules manually. Or at least on Debian I do..

    for m in /sys/class/hwmon/* ; do echo -n “$m = ” ; cat $m/name ; done

    /sys/class/hwmon/hwmon0 = nouveau
    /sys/class/hwmon/hwmon1 = k10temp
    /sys/class/hwmon/hwmon2 = asus
    /sys/class/hwmon/hwmon3 = asuswmisensors

    $sensors

    amdgpu-pci-0900
    Adapter: PCI adapter
    vddgfx:      800.00 mV 
    fan1:           0 RPM  (min =    0 RPM, max = 3200 RPM)
    edge:         +45.0°C  (crit = +100.0°C, hyst = -273.1°C)
                           (emerg = +105.0°C)
    junction:     +45.0°C  (crit = +106.0°C, hyst = -273.1°C)
                           (emerg = +111.0°C)
    mem:          +44.0°C  (crit = +105.0°C, hyst = -273.1°C)
                           (emerg = +110.0°C)
    power1:       10.00 W  (cap = 160.00 W)
    
    nvme-pci-0100
    Adapter: PCI adapter
    Composite:    +43.9°C  (low  =  -5.2°C, high = +83.8°C)
                           (crit = +87.8°C)
    
    k10temp-pci-00c3
    Adapter: PCI adapter
    Tctl:         +38.2°C  
    Tdie:         +38.2°C  
    Tccd1:        +39.8°C  
    
    asuswmisensors-isa-0000
    Adapter: ISA adapter
    CPU Core Voltage:        927.00 mV 
    VPP MEM Voltage:           2.48 V  
    +12V Voltage:             10.19 V  
    +5V Voltage:               4.96 V  
    3VSB Voltage:              3.33 V  
    VBAT Voltage:              3.23 V  
    AVCC3 Voltage:             3.33 V  
    SB 1.05V Voltage:          1.06 V  
    CPU Core Voltage:        937.00 mV 
    CPU SOC Voltage:           1.05 V  
    CPU Fan:                  910 RPM
    Chassis Fan 1:            617 RPM
    AIO Pump:                   0 RPM
    CPU OPT:                    0 RPM
    CPU Temperature:          +38.0°C  
    CPU Socket Temperature:   +38.0°C  
    Motherboard Temperature:  +37.0°C  
    Chipset Temperature:      +54.0°C  
    Tsensor 1 Temperature:   +216.0°C  
    CPU VRM Temperature:      +37.0°C  
    CPU VRM Output Current:    2.00 A

    anitX 19.4 - Core 5.10.57-antix.1-amd64-smp
    Asus B450-I , Ryzen 5 3600 , RX5600XT , 32gb 3200 , WD Black 500GB M.2 NVMe ..

    #66857
    Moderator
    ModdIt
    Helpful
    Up
    0

    xecure wrote: Moddit, I think you have confused the users.

    Helpful is great but for me things sometimes go to far…

    So go ahead and breed a new generation of persons/users who expect everything done for them because
    they are too damn lazy to search and find solutions and get all answers in the forum..

    #66881
    Member
    palacca
    Helpful
    Up
    0

    Managed to load it87 module on kernel. Now here’s the sensors output:

    sensors
    acpitz-virtual-0
    Adapter: Virtual device
    temp1:        +40.0°C  (crit = +100.0°C)
    
    it87-isa-0290
    Adapter: ISA adapter
    in0:          +1.36 V  (min =  +0.00 V, max =  +4.08 V)
    in1:          +2.46 V  (min =  +0.00 V, max =  +4.08 V)
    in2:          +3.01 V  (min =  +0.00 V, max =  +4.08 V)
    in3:          +3.04 V  (min =  +0.00 V, max =  +4.08 V)
    in4:          +2.59 V  (min =  +0.00 V, max =  +4.08 V)
    in5:          +1.63 V  (min =  +0.00 V, max =  +4.08 V)
    in6:          +2.82 V  (min =  +0.00 V, max =  +4.08 V)
    in7:          +2.85 V  (min =  +0.00 V, max =  +4.08 V)
    Vbat:         +4.08 V  
    fan1:        9000 RPM  (min = 3245 RPM)
    fan2:           0 RPM  (min =    0 RPM)
    temp1:        +62.0°C  (low  = +127.0°C, high = +101.0°C)  sensor = thermal diode
    temp2:        +45.0°C  (low  =  -1.0°C, high = +127.0°C)  sensor = thermistor
    temp3:        +27.0°C  (low  =  -1.0°C, high = +127.0°C)  sensor = thermistor
    intrusion0:  OK
    

    I can’t figure out which device temperature temp1-2-3 refer to. Which one is for cpu, if there is one?

    So go ahead and breed a new generation of persons/users who expect everything done for them because
    they are too damn lazy to search and find solutions and get all answers in the forum..

    I don’t expect anything, but one thing is for sure… as a newbie I’ve got less general knowledge, hence my searching capabilities are lower than yours.
    So yes, I still put myself to it and try to solve issues on my own (as it is way more exciting), but still after a while I may only get to dead ends.
    So here I ask, to more experienced users, as creating forums topics are and should be an important part in solving issues, for future users as myself.
    Thank you for your time, to anyone who knows if any of listed temps refer to cpu temp.

    #66890
    Member
    Xecure
    Helpful
    Up
    0

    temp1: +62.0°C (low = +127.0°C, high = +101.0°C) sensor = thermal diode

    Probably this one is the CPU, as it is the hottest.

    I don’t have much experience with looking at the sensors or temps, so I will let Koo and others who know about them to guide you on this subject.

    antiX Live system enthusiast.
    General Live Boot Parameters for antiX.

    #66945
    Member
    palacca
    Helpful
    Up
    0

    I’d think that too, but cpu-x still logs:

     CPU-X:core.c:1611: failed to retrieve CPU temperature (fallback mode)
    

    Don’t know if it’s caused by software limitations to cpu-x or if sensors still doesn’t detect any cpu temp.

    #66953
    Member
    Koo
    Helpful
    Up
    0

    I’d think that too, but cpu-x still logs:

     CPU-X:core.c:1611: failed to retrieve CPU temperature (fallback mode)
    

    Don’t know if it’s caused by software limitations to cpu-x or if sensors still doesn’t detect any cpu temp.

    This is not easy with the info you have provied or not provied. You still have not answered my question nor given any real infomation about what computer you are talking about.

    First you say you have loaded the kernel modules how have you done this. ?
    Hopfuly like this from this link. a1wong it87 chipset modules ( I have used it87 on my own board )

    Building & Installing
    ---------------------
    
    * make clean
    * make
    * sudo make install
    
    Using DKMS
    ----------
    
    To install:
    
    * sudo make dkms
    • This reply was modified 1 week, 6 days ago by Koo.

    anitX 19.4 - Core 5.10.57-antix.1-amd64-smp
    Asus B450-I , Ryzen 5 3600 , RX5600XT , 32gb 3200 , WD Black 500GB M.2 NVMe ..

    #66982
    Member
    palacca
    Helpful
    Up
    0

    mobo is Biostar P4M800-M7A rev7.0
    For loading it87 I followed various forums hint telling to change this in /etc/default/grub:

    GRUB_CMDLINE_LINUX="acpi_enforce_resources=lax"
    
    #67021
    Forum Admin
    rokytnji
    Helpful
    Up
    0

    Since search limit capabilities are mentioned.

    Refer to my signature.

    It may improve your situation.

    Sometimes I drive a crooked road to get my mind straight.
    Not all who Wander are Lost.
    I'm not outa place. I'm from outer space.

    Linux Registered User # 475019
    How to Search for AntiX solutions to your problems

    #67029
    Member
    Koo
    Helpful
    Up
    0

    @palacca
    I have looked around for your m/board model Biostar P4M800-M7A rev7.0 this one old m/board and it has a VIA chipset. I can not find any info which would help you.

    The below is add to the grub file after installing the IT87 modules, one line in grub won’t replace the modules.

    mobo is Biostar P4M800-M7A rev7.0
    For loading it87 I followed various forums hint telling to change this in /etc/default/grub:

    GRUB_CMDLINE_LINUX="acpi_enforce_resources=lax"
    

    I’m sorry can’t help you further..

    anitX 19.4 - Core 5.10.57-antix.1-amd64-smp
    Asus B450-I , Ryzen 5 3600 , RX5600XT , 32gb 3200 , WD Black 500GB M.2 NVMe ..

Viewing 14 posts - 1 through 14 (of 14 total)
  • You must be logged in to reply to this topic.